The most common form of unwanted dampness in buildings is water from the air that forms as condensation. We can offer you expert advice and guidance on how best to manage the condensation issues in your property.
The air in buildings can have a high level of relative humidity due to the activity of the occupants (e.g. cooking, bathing, drying clothes, etc.). When this water laden air comes into contact with cold surfaces such as windows and cold walls it can condense, causing water to be deposited. The point at which the water held in the air changes from vapour to liquid is known as the dew point.
Condensation is often associated with poor heating and ventilation in buildings. It is more common in winter, as the external air temperature is low and external walls and windows are cold. The usual sequence of events is as follows:
Walls in kitchens and bathrooms (where atmospheric moisture levels are usually highest), solid external walls, un-insulated solid floors and cold bridges such as concrete lintels set in cavity walls are commonly the areas in which condensation takes place.
Intermittent heating and cooling of the property can aggravate condensation problems, since it allows warm damp air to cool, reducing its capacity to hold water. Dew points are reduced allowing condensation to occur. When the air is reheated water is taken back into the air only to be deposited again when the air temperature drops again.
Running surface water on windows and walls is perhaps the most immediate indication of a condensation problem. The appearance of mould growth on internal surfaces can also occur in poorly ventilated areas. Condensation can also occur under suspended floors greatly increasing the chances of fungal decay in floor timbers.
Condensation is a real problem and where it persists, a specialist surveyor should be engaged to explore the cause of the problem and provide advice or propose solutions. We have listed just a few of the possible methods of controlling the problem below.
Simply heating the air is unlikely to be a satisfactory solution, not only on grounds of cost, but also of practicality. Unless cold surfaces are eliminated and there is sufficient background ventilation, condensation is almost inevitable. Any remedial action, therefore, must involve lowering of moisture levels, ensuring sufficient ventilation and the elimination of cold surfaces.
Improved heating and ventilation coupled with specific action in relation to cold spots will usually result in a significant improvement in conditions, although there may be circumstances in which alternative methods are required. A modest but constant background heat is preferable to intermittent heating since this will help to maintain a higher ambient temperature in the fabric of the building.
The installation of suitable extractor fans in the moisture producing rooms of a property such as the kitchen, bathroom and en-suites, will help remove the majority of this moisture-laden air from these areas (that are most responsible for condensation), with minimal running costs. This is a requirement within the Building Regulations for new properties being built, whilst also applying to existing buildings.
There are many different types of extractor fans available such as those that run continuously in the background or those which incorporate a humidistat which will control the operation of the fan within certain humidity limits. It is also possible to install fans that have an integrated heat exchanger and these have the advantage of providing effective ventilation while reducing heat loss from the property. It is very important that these types of fans are professionally specified and commissioned by a suitably trained and qualified specialist.
Where an open fire or fixed gas fire exists, a certain amount of “natural” ventilation will occur and where additional ventilation is provided it is important that this is not blocked off.
The use of specialist insulation materials fixed to the outside of the building and insulation in cavity walls will help to improve the thermal dynamics of the building and may help overcome condensation.
An alternative to heating and ventilation for the control of moisture in the air is a dehumidifier. This is a device which draws in air, cools it to remove moisture which is collected in a reservoir and reheats it to an acceptable temperature before re-circulating it – these can be costly to run however, and may not be considered a long-term solution.
Other devices that may be considered are positive pressure condensation control units also known as Positive Input Ventilation (PIV) units. These take dryer air from roof spaces or lofts and mix this with air in the dwelling. This is done at a very low rate (below half an air change per hour) and has the effect of lowering total moisture content and removing moist air by natural leakage.
Please contact us to discuss your requirements and we will do our utmost to assist you. Insitu SCP are one of the most established names in building preservation in the South East of England, with over 40 years experience in the industry. You can be assured that we will identify potential issues, find the best solution and deliver long lasting results with minimal disruption.